MATERIAL SAFETY DATA SHEET

1. PRODUCT AND COMPANY IDENTIFICATION

PRODUCT NAME : M290G15/M290G20/M290G33/M290G43/M290G50 COMPANY NAME : Lixin Engineering Plastics Co., Ltd

COMPANY ADDRESS : EAST CITY WAIJING INDUSTRY GARDEN,SHANHU ROAD NIUSHAN

COUNTRY,EAST CITY SECTION,DONGGUAN,GUANG DONG

PROVINCE,CHINA

TEL : +86-0769-********

FAX : +86-0769-********

EMERGENCY TEL : +86-0769-********

2. COMPOSITION / INFORMATION ON INGREDIENTS

SINGLE CHEMICAL SUBSTANCE OR MIXTURE Mixture

CHEMICAL NAME : Polyhexamethylene adipamide (Polyamide 66)

COMPOSITION : Polyamide 66 45-85%

Glass fiber 13-50%

Other additives 2-5%

CHEMICAL OR STRUCTURAL FORMULA :

~ { ( NH – (CH2)6 – NH ) (C – (CH2)4 – C ) }n ~

‖‖

o o

CAS NO. : Principal ingredient 3 2 1 3 1 – 17 - 2

UN CLASSFICATION & UN NO. : Not applicable

OSHA HAZARDS

(29 CFR 1910.1200) :

OSHA PEL ACGIH TWA

Antimony trioxide 0.5mg/m (As Sb)m³ 0.5mg/m³(As Sb)

ADDITIVES : Light-stabiliser, heat-stabiliser, lubricant,

nuclear-agent, etc. are added, if necessary. These

additives are not hazardous by OSHA‘s Hazard

Communication Standards.EMERGENCY OVERVIEW :

- Skin contact of molten resin causes thermal burn.

- Inhalation of gas from molten resin causes nausea.

- Gas generated during drying and melting causes eye and skin irritation.

POTENTIAL HEALTH EFFECTS:

EYE : Contact with molten resin causes thermal burn.

SKIN : Contact with molten resin causes thermal burn.

INHALATION : Inhalation of gas from molten resin may cause

nausea.

INGESTION : In antimony trioxide, the oral LD50 in rats is over

20g/kg. Swallowing may cause injury.

CARCINOGENICITY : Antimony trioxide is listed by IARC 2B possibly

carcinogenic to humans.

4.FIRST-AID MEASURES

EYE CONTACT : If the material is in a molten state, immediately cool and wash with clean water for at least 15 minutes. Remove contact lenses, if worn, unless they have

adhered to eyes, and seek medical attention.

SKIN CONTACT: If the material is in a molten state, cool with clean water immediately. Do not forcibly remove any solidified resin stuck to the skin, but continue cooling until it

becomes readily removable. Get medical attention for thermal burn. INHALATION : If inhalation of gas from molten resin causes nausea, remove the individual to fresh air and keep him at rest for recovery. If he does not recover, seek medical

attention.

INGESTION : Induce vomiting only if the victim is conscious. In case of heavy ingestion, seek medical attention.

5.FIRE-FIGHTING MEASURES

EXTINGUISHING METHOD AND SPECIFIC HAZARDS:

- Extinguishing with water is the preferred method.

- Hazardous gases (CO2,CO, a trace of HCN,NH3,halide etc. ) may be produced during a fire.

EXTINGUISHING MEDIA: Water, foam, powder.

6.ACCIDENTAL RELEASE MEASURESdisposed of properly. (Method of disposal must be in compliance with the section 14. DISPOSAL CONSIDERATIONS below. )

7.HANDLING AND STORAGE

HANDLING:

-Take care so as not to inhale gas during processing of the material.

-Do not hold the material at high temperatures over an extended time.

STORAGE :

-Store the material away from heat and ignition sources.

8.EXPOSURE CONTROL / PERSONAL PROTECTION

EXPOSURE LIMITS : Not establish for product as whole. Refer to Section 2

for a hazardous component.

TLVS ACGIH (1993-1994) : Nuisance Dust 10mg/m³

ENGINEERING MEASURE : In cases where possibilities of dust formation,

gas generation, or vapor emission exist, it is desirable to

provide local ventilation.

PERSONAL PROTECTIVE EQUIPMENT :

RESPIRATORY PROTECTION : Wear as needed.

EYE PROTECTION : Wear as needed.

HAND PROTECTION : Wear as needed.

SKIN PROTECTION : Wear as needed.

9.PHYSICAL & CHEMIICAL PROPERTIES

APPEARANCE : Pellets

VOLATILITY : None

SPECIFIC GRAVITY : 1.4-1.6

MELTING POINT : ≥ 240°C

SOLUBILITY IN WATER : Insoluble

10.STABILITY & REACTIVITY

AUTOIGNITION TEMPERATURE : ≥ 400°C

FLAMMABILITY : flammable

STORAGE STABILITY : Stable at room temperature

REACTIVITY WITH WATER : None

OXIDIZING PROPERTY : None

SELF-REACTIVITY / POTENTIAL FOR EXPLOSION: None

11.TOXICOLOGICAL INFORMATIONIRRITANT PROPERTY : Gas generated during drying and melting is irritant to eyes and skin. OTHER INFORMATION : Not available for product as whole. Refer to Section 3.

12.ECOLOGICAL INFORMATION

Never dump or discharge this material into ocean or any other body of water to avoid ingestion by marine life or birds.

13.DISPOSAL CONSIDERATIONS

Disposal of this material, whether by landfill or by incineration, must be in compliance with the laws and regulations for environmental protection which are applicable to this material in the users’ countries.

Hazardous gases ( CO2, CO, a trace of HCN, NH3, halide, etc. )may be generated during incineration.

14.TRANSPORT INFORMATION

Avoid water contact and violent handling to prevent bag rupture.

In the event of bag rupture and pellet spill, be careful not to slip and fall.

15.REGULATORY INFORMATION

US Federal Regulations:

OSHA : Antimony trioxide is hazardous by definition of Hazard Communication Standards ( 29 CFR 1910.1200 ) .

CERCLA : SECTION 313

This product contains NONE of the substances subject to the reporting requirements of SECTION 313 of Title Ⅲ of the superfund Amendments and Reauthorization ACT of 1986 and 40 CFR 372.

SECTION 311 / 102

This product contains Reportable Quantity ( RQ ) Substance subject to the reporting requirements of SECTION 311 of THE CLEAN WATER ACT and 40 CFR 117, and of SECTION 102 of CERCLA and 40 CFR 302.

RQ (Final) of this substance is 1000 pounds.

16.OTHER INFORMATION

For further information, please contact:

Lixin Engineering Plastics Co.

Phone: +86-0769-******** FAX: +86-0769-********

NOTE :This information is furnished without warranty expressed or implied, expect that it is accurate to the best knowledge of Lixin Engineering Plastics Co. The data on this sheet related only to the specific material designated herein. Lixin Engineering Plastics Co. Assumes no legal responsibility for use or reliance upon these data.下载本文