Cisco与Brocade光纤交换机级联配置文档_动视

Cisco与Brocade光纤交换机级联配置文档

2025-09-24 06:37:49 责编:小OO

点击下载本文 文档为doc格式

Cisco与Brocade光纤交换机级联配置文档

Cisco 9120交换机

用户名：admin

密码：bsczzf912o(o为字母o)

1.配置异构交换机平台协同工作模式

Cisco 9120配置过程

激活前8个端口

switch# config t

Enter configuration commands, one per line. End with CNTL/Z.

switch(config)#interface fc1/1-8

switch(config-if)# no shutdownswitch(config-if)# end

配置交换机协同工作模式

switch# config t

Enter configuration commands, one per line. End with CNTL/Z.

switch(config)# vsan database

switch(config-vsan-db)# vsan 1 interop

switch(config-vsan-db)# end

配置domain ID

switch# config t

Enter configuration commands, one per line. End with CNTL/Z.

switch(config)# fcdomain domain 100 preferred vsan 1

switch(config)# end

激活VSAN

switch# config t

Enter configuration commands, one per line. End with CNTL/Z.

switch(config)# vsan database

switch(config-vsan-db)# vsan 1 suspend

switch(config-vsan-db)# no vsan 1 suspend

switch(config-vsan-db)# end

察看修改之后的系统配置信息

switch# show running

version 2.0(2b)

vsan database

vsan 1 interop 1

fcdomain domain 100 preferred vsan 1

fcdomain fcid persistent vsan 1

boot kickstart bootflash:/m9100-s1ek9-kickstart-mz.2.0.2b.bin

boot system bootflash:/m9100-s1ek9-mz.2.0.2b.bin

kernel core target 0.0.0.0

kernel core limit 1

snmp-server user admin network-admin auth md5 0xeecba2afbe9b65e13b23882ac6ae05

priv 0xeecba2afbe9b65e13b23882ac6ae05 localizedkey

username admin password 5 $1$V3smTQpb$MTvub69DkVBxdCt9BsEDB1 role network-admin

callhome

switch-priority 7

snmp-server enable traps license

interface mgmt0

ip address 192.168.70.139 255.255.255.0

interface fc1/1

no shutdown

interface fc1/2

no shutdown

interface fc1/3

no shutdown

interface fc1/4

no shutdown

interface fc1/5

no shutdown

interface fc1/6

no shutdown

interface fc1/7

no shutdown

interface fc1/8

no shutdown

interface fc1/9

interface fc1/10

interface fc1/11

interface fc1/12

interface fc1/13

interface fc1/14

interface fc1/15

interface fc1/16

interface fc1/17

interface fc1/18

interface fc1/19

interface fc1/20

switch#

察看端口连接状态信息

switch# show interface brief

-------------------------------------------------------------------------------

Interface Vsan Admin Admin Status FCOT Oper Oper Port

Mode Trunk Mode Speed Channel

Mode (Gbps)

-------------------------------------------------------------------------------

fc1/1 1 auto on up swl F 2 --

fc1/2 1 auto on up swl F 2 --

fc1/3 1 auto on up swl E 2 --

fc1/4 1 auto on notConnected swl -- --

fc1/5 1 FX -- notConnected swl -- --

fc1/6 1 FX -- notConnected swl -- --

fc1/7 1 FX -- notConnected swl -- --

fc1/8 1 FX -- notConnected swl -- --

fc1/9 1 FX -- sfpAbsent -- -- --

fc1/10 1 FX -- sfpAbsent -- -- --

fc1/11 1 FX -- sfpAbsent -- -- --

fc1/12 1 FX -- sfpAbsent -- -- --

fc1/13 1 FX -- sfpAbsent -- -- --

fc1/14 1 FX -- sfpAbsent -- -- --

fc1/15 1 FX -- sfpAbsent -- -- --

fc1/16 1 FX -- sfpAbsent -- -- --

fc1/18 1 FX -- sfpAbsent -- -- --

fc1/19 1 FX -- sfpAbsent -- -- --

fc1/20 1 FX -- sfpAbsent -- -- --

刀片中心光纤交换机模块配置(brocade)

禁止交换机

brocadessm:USERID> switchdisable

修改Domain ID

brocadessm:USERID> configure

Configure...

Fabric parameters (yes, y, no, n): [no] yes

Domain: (1..239) [1] 99

R_A_TOV: (4000..120000) [10000]

E_D_TOV: (1000..5000) [2000]

WAN_TOV: (0..30000) [0]

MAX_HOPS: (7..19) [7]

Data field size: (256..2112) [2112]

Sequence Level Switching: (0..1) [0]

Disable Device Probing: (0..1) [0]

Suppress Class F Traffic: (0..1) [0]

Switch PID Format: (1..2) [1]

Per-frame Route Priority: (0..1) [0]

Long Distance Fabric: (0..1) [0]

BB credit: (1..27) [16]

Insistent Domain ID Mode (yes, y, no, n): [no]

Virtual Channel parameters (yes, y, no, n): [no]

Zoning Operation parameters (yes, y, no, n): [no]

RSCN Transmission Mode (yes, y, no, n): [no]

Arbitrated Loop parameters (yes, y, no, n): [no]

System services (yes, y, no, n): [no]

Portlog events enable (yes, y, no, n): [no]

ssl attributes (yes, y, no, n): [no]

http attributes (yes, y, no, n): [no]

snmp attributes (yes, y, no, n): [no]

rpcd attributes (yes, y, no, n): [no]

cfgload attributes (yes, y, no, n): [no]

webtools attributes (yes, y, no, n): [no]

WARNING: The domain ID will be changed. The port level zoning may be affected

brocadessm:USERID> msPlMgmtDeactivate

Switch is in Offline state.

修改协同工作模式

brocadessm:USERID> interoper mode 1

The switch effective configuration will be lost when the operating mode is changed; do you want to continue? (yes, y, no, n): [no] y

Interopmode is enabled

Note: It is recommended that you reboot this switch for the new change to take effect.

重新引导交换机

brocadessm:USERID> fastboot

Broadcast message from root (pts/0) Tue Jun 13 10:07:45 2006...The system is going down for reboot NOW !!USERID

Password:

Please change your passwords now.

Use Control-C to exit or press 'Enter' key to proceed.

Password was not changed. Will prompt again at next login

until password is changed.

brocadessm:USERID>

激活交换机

brocadessm:USERID> switchenable

察看修改配置之后的交换机状态

brocadessm:USERID> switchshow

switchName: brocadessm

switchType: 22.0

switchState: Online

switchMode: Interop

switchRole: Principal

switchDomain: 99

switchId: fffc63

switchWwn: 10:00:00:05:1e:02:78:c6

zoning: OFF

switchBeacon: OFF

Area Port Media Speed State

==============================

0 0 id 2G No_Light

1 1 cu 2G Online F-Port 21:00:00:14:5e:24:a9:04

2 2 cu 2G Online F-Port 21:00:00:14:5e:24:a9:36

3 3 cu 2G Online F-Port 21:00:00:14:5e:24:a9:7a

4 4 cu 2G Online F-Port 21:00:00:14:5e:24:a9:b6

5 5 cu 2G Online F-Port 21:00:00:14:5e:24:a9:28

6 6 cu 2G Online F-Port 21:00:00:14:5e:24:aa:f6

7 7 cu 2G Online F-Port 21:00:00:14:5e:24:aa:f0

8 8 cu 2G Online F-Port 21:00:00:14:5e:24:a9:38

9 9 cu 2G No_Light

10 10 cu 2G No_Light

11 11 cu 2G No_Light

12 12 cu 2G No_Light

13 13 cu 2G No_Light

14 14 cu 2G No_Light

15 15 id 2G Online E-Port 20:01:00:0d:ec:06:b4:41 (downstream)

2.划分zone

Cisco 9120划分zone

察看fabric连接设备port wwn 信息

switch# show fcns database vsan 1

VSAN 1:

--------------------------------------------------------------------------

FCID TYPE PWWN (VENDOR) FC4-TYPE:FEATURE

--------------------------------------------------------------------------

0x630100 N 21:00:00:14:5e:24:a9:04 scsi-fcp

0x630200 N 21:00:00:14:5e:24:a9:36 scsi-fcp

0x630300 N 21:00:00:14:5e:24:a9:7a scsi-fcp

0x630400 N 21:00:00:14:5e:24:a9:b6 scsi-fcp

0x630500 N 21:00:00:14:5e:24:a9:28 scsi-fcp

0x630600 N 21:00:00:14:5e:24:aa:f6 scsi-fcp

0x630700 N 21:00:00:14:5e:24:aa:f0 scsi-fcp

0x630800 N 21:00:00:14:5e:24:a9:38 scsi-fcp

0x0000 N 20:07:00:a0:b8:21:19:9f (SymBios) scsi-fcp:both

0x0100 N 20:06:00:a0:b8:21:19:9f (SymBios) scsi-fcp:both

Total number of entries = 10

创建zone

分别创建2个zone，前4个刀片服务器与DS4300 2个控制器组成的zone，第4到第8个刀片服务器与DS4300 2个控制器组成的zone。

switch# config tEnter configuration commands, one per line. End with CNTL/Z.

switch(config)# zone name blade_hs20_1-4 vsan 1switch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:04switch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:36switch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:7aswitch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:b6switch(config-zone)# member pwwn 20:07:00:a0:b8:21:19:9fswitch(config-zone)# member pwwn 20:06:00:a0:b8:21:19:9f

switch(config-zone)#exit

switch(config)# zone name blade_hs20_5-8 vsan 1

switch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:28switch(config-zone)# member pwwn 21:00:00:14:5e:24:aa:f6switch(config-zone)# member pwwn 21:00:00:14:5e:24:aa:f0switch(config-zone)# member pwwn 21:00:00:14:5e:24:a9:38switch(config-zone)# member pwwn 20:07:00:a0:b8:21:19:9fswitch(config-zone)# member pwwn 20:06:00:a0:b8:21:19:9f

创建zoneset

switch(config-zone)# zoneset name ds4300_blade vsan 1switch(config-zoneset)# member Blade_Hs20_1-4

switch(config-zoneset)# member Blade_Hs20_5-8

switch(config-zoneset)# end

激活zonesetswitch# config tEnter configuration commands, one per line. End with CNTL/Z.

switch(config)# zoneset activate name ds4300_blade vsan 1Zoneset activation initiated. check zone status

察看激活的zone信息

switch# show zone active vsan 1

zone name blade_hs20_1-4 vsan 1

* fcid 0x630100 [pwwn 21:00:00:14:5e:24:a9:04]

* fcid 0x630200 [pwwn 21:00:00:14:5e:24:a9:36]

* fcid 0x630300 [pwwn 21:00:00:14:5e:24:a9:7a]

* fcid 0x630400 [pwwn 21:00:00:14:5e:24:a9:b6]

* fcid 0x0000 [pwwn 20:07:00:a0:b8:21:19:9f]

* fcid 0x0100 [pwwn 20:06:00:a0:b8:21:19:9f]

zone name blade_hs20_5-8 vsan 1

* fcid 0x630500 [pwwn 21:00:00:14:5e:24:a9:28]

* fcid 0x630600 [pwwn 21:00:00:14:5e:24:aa:f6]

* fcid 0x630700 [pwwn 21:00:00:14:5e:24:aa:f0]

* fcid 0x630800 [pwwn 21:00:00:14:5e:24:a9:38]

* fcid 0x0000 [pwwn 20:07:00:a0:b8:21:19:9f]

* fcid 0x0100 [pwwn 20:06:00:a0:b8:21:19:9f]

保存系统配置信息

switch# copy running startup

[########################################] 100%

刀片中心光纤交换机模块查看zone信息

brocadessm:USERID> cfgshow

Defined configuration:

no configuration defined

Effective configuration:

cfg: ds4300_blade

zone: blade_hs20_1-4

21:00:00:14:5e:24:a9:04

21:00:00:14:5e:24:a9:36

21:00:00:14:5e:24:a9:7a

21:00:00:14:5e:24:a9:b6

20:07:00:a0:b8:21:19:9f

20:06:00:a0:b8:21:19:9f

zone: blade_hs20_5-8

21:00:00:14:5e:24:a9:28

21:00:00:14:5e:24:aa:f6

21:00:00:14:5e:24:aa:f0

21:00:00:14:5e:24:a9:38

20:07:00:a0:b8:21:19:9f

20:06:00:a0:b8:21:19:9f

如上命令输出所示，Cisco 9120的zone 信息已经同步到刀片中心的交换机模块。

系统配置完成。下载本文

显示全文

全部频道